FEATURES for SDP 50 CIX

• Performance Graphs SDP 50 CIX
  

  • Performance as measured pumping water at 20 deg C
  • Disclaimer: Actual pump performance may vary depending on number of bends, suction needed and friction in length of discharge piping.
  • For guidance on how to select a suitable pump, visit Teryair AODD
• Dimension diagram SDP 50 CIX
  
• Diaphragm Options SDP 50 CIX

  Type of Diaphragm	Image	Typical Usage
  Neoprene		An excellent general purpose diaphragm for use in non-aggressive applications such as water- based slurries, well water or sea water. Exhibits excellent flex life and low cost. Temperature range -18 C to +93 C (0 F to +200 F)
  Nitrile		Excellent for applications involving petroleum / oil-based fluids such as leaded gasolines, fuel oils, non-synthetic hydraulic oils, kerosene, turpentine and motor oils. Temperature range -12 C to +82 C (+10 F to +180 F)
  Santoprene		Good abrasion resistance. Low cost. Can handle mild acids and alkalis well. Excellent low cost alternative to ptfe. Excellent suction capabilites, Excellent general purpose diaphragm. Temperature range -40 C to +107 C (-40 F to +225 F)
  Hytrel		Good abrasion resistance. Low cost. Excellent suction capabilites. Good general purpose diaphragm. Temperature range -29 C to +104 C (-20 F to +220 F)
  Viton		Excellent for use in applications requiring extremly hot temperatures. May also be used with aggressive fluids such as aromatic or chlorinated hydrocarbons and highly aggressive acids. Especially where high suction lift is important. Temperature range -40 C to +177 C (-40 F to + 350 F)
  Note: not all diaphragm options may be available with all pumps. See above for diaphragms available with this pump.

• Pump Nomenclature

  XX	XX	XX	X	X	X
  Air Valve Type	Pump Size	Material of Construction	Material of Diaphragm	Bolted or Clamped	Threading on Inlet and Outlet
  DP - Classic ADP - Advanced SDP - MaxFlo	06 - 1/4”	AL - Aluminum SS - Stainless Steel 316L PP - Polypropylene CI - Ductile Iron PD - PVDF	B - Nitrile N - Neoprene S - Santoprene T - PTFE V - Viton H - Hytrel	B - Bolted C - Clamped	R- NPT G - BSPT P - BSPP F - Flanged
  	12 - 1/2”
  	15 - 1/2”
  	30/25 - 1”
  	40 - 1 - 1/2”
  	50 - 2 “
  	75- 3”
  	100 - 4”

• ATEX Code

  Pump Size	Series	Wetted Materials	Center Section	Dipharagm Materials	ATEX Rating
  50 (2")	SDP	Cast Iron	Cast Iron	Neoprene	ll 2 GD Ex h IIC T6 Gb Ex h IIIC T85⁰C Db I M2 Ex h I Mb (IP65)
  				Buna-N
  				Viton-FKM	ll 2 GD Ex h IIC T3 Gb Ex h IIIC T200⁰C Db (IP65) I M2 Ex h I Mb (IP65)
  				Sentoprene	ll 2 GD Ex h IIC T5 Gb Ex h IIIC T100⁰C Db (IP65) I M2 Ex h I Mb (IP65)
  				Hytrel
  				PTFE